Jumper X86 Micro FPV Racer 3S

Den Jumper X86 gibt es bei Banggood für ca. 48€ mit 20% Coupon Code: LDHH – https://goo.gl/HJZ9MQ
Man braucht ein 450mAh 2S 65C Lipo zB von Tattu oder nano-Tech und schon kann es losgehen. Der Jumper X86 ist sehr robust und nach dieser kleinen Modifikation 3S fähig. Da muss der 5V BEC ausgetauscht werden und schon fliegt er schneller mit 3S LiPo. Und man sollte bessere Propeller verwenden z.B. RacerStar oder GemFan 2035.
Um noch besser den Jumper X86 zu machen kauft man ein 10A oder 12A ESC 4in1 Block und tauscht den gegen die 4 ESC’s. dann ist der Racer 15 Gramm leichte und fliegt sich noch besser.

Teile die ich für Jumper X86 verwendet habe:
Racerstar 2035 50mm Propeller 25% mit coupon: MRPC – https://goo.gl/XBns3P
GemFan 2035BN RotorX Propeller – https://goo.gl/RaBJc2
Matek BEC 5V 1,5A – https://goo.gl/YP85GM
oder Diatone Mini 2A BEC 5V – https://goo.gl/aTDdNE
Amass XT30 Plug – https://goo.gl/vSw6fT
18AWG Silicone Cable für 3S – https://goo.gl/TcRHyv

Mehr Quadcopter mit 20% off: LDHH – https://goo.gl/3o29eh
Mehr Ersatzteile mit 25% off: MRPC – https://goo.gl/rGB1e6

Video 1 – Jumper X86 3S LiPo mod – Umbau

Video 2 – Flug 2S nano-tech 3S Tattoo 75C Gemfan 2035

Konfiguration

Auf dem FC ist Betaflight 3.2 mit folgenden Änderungen (diff):

# diff 2017-09-14
# Betaflight / OMNIBUS (OMNI) 3.2.0 Sep 11 2017 RC5
name Jumper86
feature AIRMODE
feature ANTI_GRAVITY
feature DYNAMIC_FILTER
beeper -BAT_LOW
beeper -ON_USB
map TAER1234
aux 0 0 0 1700 2100
aux 1 1 1 900 1250
aux 2 2 1 1300 1700
aux 3 13 2 1700 2100
rxfail 3 h
set gyro_notch1_hz = 0
set gyro_notch2_hz = 0
set baro_hardware = NONE
set min_check = 1040
set max_check = 1990
set rssi_channel = 8
set fpv_mix_degrees = 15
set serialrx_provider = SBUS
set motor_pwm_protocol = DSHOT600
set align_board_yaw = 180
set vbat_min_cell_voltage = 31
set vbat_warning_cell_voltage = 33
set ibata_scale = 600
set ibata_offset = 561
set deadband = 2
set yaw_deadband = 2
set pid_process_denom = 2
set osd_vbat_pos = 2511
set osd_rssi_pos = 2061
set osd_tim_1_pos = 54
set osd_tim_2_pos = 2519
set osd_flymode_pos = 2505
set osd_throttle_pos = 225
set osd_vtx_channel_pos = 377
set osd_crosshairs = 200
set osd_ah_sbar = 200
set osd_ah_pos = 200
set osd_current_pos = 2048
set osd_mah_drawn_pos = 353
set osd_craft_name_pos = 2496
set osd_gps_speed_pos = 218
set osd_gps_lon_pos = 82
set osd_gps_lat_pos = 65
set osd_gps_sats_pos = 51
set osd_home_dir_pos = 302
set osd_home_dist_pos = 303
set osd_compass_bar_pos = 266
set osd_altitude_pos = 247
set osd_pid_roll_pos = 423
set osd_pid_pitch_pos = 455
set osd_pid_yaw_pos = 487
set osd_debug_pos = 1
set osd_power_pos = 321
set osd_pidrate_profile_pos = 2075
set osd_warnings_pos = 329
set osd_avg_cell_voltage_pos = 76
set osd_pit_ang_pos = 257
set osd_rol_ang_pos = 289
set osd_battery_usage_pos = 392
set osd_disarmed_pos = 2410
set osd_nheading_pos = 311
set osd_nvario_pos = 279
set osd_esc_tmp_pos = 82
set osd_esc_rpm_pos = 83
set vcd_video_system = 1
profile 2
set dterm_lowpass_type = PT1
profile 1
set dterm_lowpass_type = PT1
set dterm_notch_hz = 0
set p_pitch = 60
set i_pitch = 45
set d_pitch = 27
set p_roll = 50
set i_roll = 45
set d_roll = 27
set p_yaw = 80
set level_limit = 65
profile 0
set dterm_lowpass_type = PT1
set dterm_notch_hz = 0
set p_pitch = 22
set i_pitch = 20
set d_pitch = 18
set p_roll = 22
set i_roll = 20
set d_roll = 18
rateprofile 0
set roll_srate = 75
set pitch_srate = 75
set yaw_srate = 75
save

Mein Equipment:
Skyzone SKY02S V+ Brille – https://goo.gl/Wrznsr
FrSky TARANIS Q X7 Funke – https://goo.gl/rrWdfy
FrSky X9D Plus SE Funke – https://goo.gl/A6Fg1O
iRangeX IRX4 Multiprotokol Modul – https://goo.gl/uxMROJ
FrSky XM Empfänger – https://goo.gl/eBdJzS
FrSky XM+ Empfänger – https://goo.gl/9tZT2h
FlySky FS-i6X Funke – https://goo.gl/iyrmSM
FlySky FS-i6 Funke – https://goo.gl/mWdxbS
FlySky A8S Empfänger – https://goo.gl/PrVerD
RunCam 2 Actiocam – https://goo.gl/x12sNP
RunCam 3 Actiocam – https://goo.gl/twCyP6
RunCam Micro Swift – https://goo.gl/8Vpva9
RunCam Swift Mini – https://goo.gl/sCPAEP