Reptile Cloud 149 CineWhoop

Reptile CLOUD-149 ist ein 3 Zoll Mega CineWhoop. Für wenig Geld bekommt man einen soliden Quad zum Video Filmen mit z.B. einer GoPro Kamera.
Hole dir den Reptile CLOUD-149 aus [CZ] EU Lager mit dem Coupon: BGaFf10oFf – https://www.banggood.com/custlink/3Dvvl7sWcf
Schnelle Lieferung aus CZ.
Coupon2: BGRE149

Video 1 – Reptile Cloud 149 CineWhoop gut und günstig

Der fertiger 3 Zoll CyneWhoop hat 20A ESC’s, F4 FC, 1407 4000KV Motoren, 25-500mW VTX Video Sender.

In der Lieferung ist der Reptile CLOUD-149 flugfertig ohne einem Empfänger PNP mit einer GoPro 6-7 Halterung.

Schnelle 1408 4000KV Motoren. Laufen sehr gut mit 4S und sogar mit 3S gut zu fliegen.

Gesamtgewicht mit GoPro Session 5 und einem 4S 1550mAh Akku 476 Gramm

Leergewicht 214 Gramm

Video Sender 25 bis 500mW
Der Sender ist der EWRF 7092TM Pro 5.8G 40CH 25/200/500mW Power Adjustable U.FL FPV Transmitter Support Pitmode OSD Configuring VTX
https://www.banggood.com/custlink/Km3yEFSQye

Verwendeter F4 FC ist ein 20x20mm HAKRC MiniF4 F4 Flight Controller AIO Betaflight OSD & 5V 2A BEC Support INAV for RC Drone
https://www.banggood.com/custlink/KGmEdPVAOs
Für iBUS muss die Brücke zusammengelötet werden und unter Betaflight wird für iBUS Flysky Empfänger UART6 eingestellt unter PORTS.

Die ESC’s sind 20A BLHELI_S die HAKRC 20x20mm 20A BLheli_S BB2 2-4S 4 in 1 Brushless ESC Support DShot600

https://www.banggood.com/custlink/3KvhyP85cs

Ersatzteile für Reptile Cloud findest Du hier:
https://www.banggood.com/custlink/v3vEYtlPWI

Interessant ist das Schaumstoff Schutz für die Propeller Ducts
https://www.banggood.com/custlink/Kvmyd5aiz6

Die FPV Kamera ist mit 16:9 Seitenverhältnis. Ok, aber nicht gut genug für nicht. Eine CADDX F2 oder Foxeer Falkor wäre mir hier lieber.

Foxeer Micro Falkor 2 1200TVL FPV Kamera – https://www.banggood.com/custlink/mvvv0aHs02

Caddx Turbo Micro F2 Kamera
– https://www.banggood.com/custlink/3vmG6GhUUK

Die Bodenplatte mit den Armen ist 3mm dick

Duct 3 Zoll 3045 Propeller

iFlight MegaBee V2 3045 3 Zoll 3-Blatt Propeller – https://www.banggood.com/custlink/GmmDzETVB0

GoPro 6,7 Halterung. Leider mit zu grossem Neigungswinkel von über 25 Grad

Hinten eine RHCP Antenne mit einem SMA Anschluss

Pro:
– Gutes Flugverhalten
– preiswert
– guter Video Sender 500mW HGLRC
– Guter Propeller Schutz aus Kunstoff
– F4 FC HGLRC
– 20A DSHOT600 ESC’s HGLRC

Contra:
– schlechte 16:9 FPV Kamera
– Betaflight nicht eingestellt
– GoPro Halterung über 25 Grad

Meine Einstellungen 2020-03-01 mit BlHeli 2.70
# 8k 8k Profil 1 recht ruhig
# Profi2 etwas schlechter als Profil 1

# 2020-03-01 BlHeli 2.70 8k 8k profile 1 with rate profile 2
# diff all
# version
# Betaflight / STM32F405 (S405) 4.1.4 Feb  4 2020 / 17:25:51 (bc9715eec) MSP API: 1.42
# manufacturer_id: AIRB   board_name: OMNIBUSF4SD   custom defaults: YES
# start the command batch
batch start
# reset configuration to default settings
defaults nosave
board_name OMNIBUSF4SD
manufacturer_id AIRB
mcu_id 0052002f324d500220313256
signature 
# name: CLOUD-149
# feature
feature TELEMETRY
# beeper
beeper -GYRO_CALIBRATED
beeper -DISARMING
beeper -ARMING
beeper -ARMING_GPS_FIX
beeper -GPS_STATUS
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -DISARM_REPEAT
beeper -ARMED
beeper -SYSTEM_INIT
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH_FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSE
beeper -RC_SMOOTHING_INIT_FAIL
# beacon
beacon RX_LOST
beacon RX_SET
# map
map TAER1234
# serial
serial 0 64 115200 57600 0 115200
serial 2 2048 115200 57600 0 115200
serial 5 0 115200 57600 0 115200
# aux
aux 0 0 0 1700 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 2 1700 2100 0 0
aux 4 35 2 1300 1700 0 0
# rxrange
rxrange 0 987 2011
rxrange 1 987 2011
rxrange 2 987 2011
rxrange 3 987 2011
# vtxtable
vtxtable bands 5
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 5645 5885 5905 5925 5945
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable powerlevels 3
vtxtable powervalues 0 1 2
vtxtable powerlabels 25 200 500
# master
set gyro_lowpass2_hz = 325
set dyn_notch_range = AUTO
set dyn_lpf_gyro_min_hz = 260
set dyn_lpf_gyro_max_hz = 650
set acc_calibration = 6,35,-139
set mag_hardware = NONE
set min_check = 1010
set max_check = 1990
set fpv_mix_degrees = 15
set serialrx_provider = SBUS
set dshot_idle_value = 400
set motor_pwm_protocol = DSHOT600
set motor_poles = 12
set vbat_max_cell_voltage = 450
set beeper_dshot_beacon_tone = 5
set small_angle = 180
set pid_process_denom = 1
set osd_warn_esc_fail = OFF
set osd_warn_core_temp = OFF
set osd_vbat_pos = 2498
set osd_rssi_pos = 33
set osd_tim_1_pos = 34
set osd_tim_2_pos = 2519
set osd_flymode_pos = 2487
set osd_throttle_pos = 321
set osd_vtx_channel_pos = 52
set osd_crosshairs_pos = 2317
set osd_craft_name_pos = 2506
set osd_warnings_pos = 2473
set debug_mode = SMARTAUDIO
set vtx_band = 4
set vtx_channel = 1
set vtx_power = 1
set vtx_freq = 5740
set gyro_1_align_yaw = 2700
set name = CLOUD-149
profile 0
# profile 0
set dyn_lpf_dterm_min_hz = 91
set dyn_lpf_dterm_max_hz = 221
set dterm_lowpass2_hz = 195
set feedforward_transition = 30
set p_pitch = 41
set d_pitch = 57
set f_pitch = 162
set p_roll = 38
set d_roll = 53
set f_roll = 153
set p_yaw = 45
set f_yaw = 111
set angle_level_strength = 40
set d_min_roll = 30
set d_min_pitch = 33
profile 1
# profile 1
set dyn_lpf_dterm_min_hz = 105
set dyn_lpf_dterm_max_hz = 255
set dterm_lowpass2_hz = 225
set feedforward_transition = 30
set p_pitch = 51
set d_pitch = 53
set f_pitch = 162
set p_roll = 47
set d_roll = 49
set f_roll = 153
set p_yaw = 42
set f_yaw = 111
set angle_level_strength = 40
set d_min_roll = 28
set d_min_pitch = 31
profile 2
# restore original profile selection
profile 0
rateprofile 0
# rateprofile 0
set yaw_rc_rate = 210
set roll_srate = 65
set pitch_srate = 65
set yaw_srate = 20
set tpa_rate = 50
set tpa_breakpoint = 1750
rateprofile 1
# rateprofile 1
set thr_expo = 40
set roll_srate = 60
set pitch_srate = 60
set yaw_srate = 60
rateprofile 2
rateprofile 3
rateprofile 4
rateprofile 5
# restore original rateprofile selection
rateprofile 1
# save configuration
save

Original diff 2020-02-24

# diff all
# version
# Betaflight / OMNIBUSF4SD (OBSD) 4.0.4 Jun 30 2019 / 14:43:06 (f3a95efa3) MSP API: 1.41
# start the command batch
batch start
# reset configuration to default settings
defaults nosave
board_name OMNIBUSF4SD
manufacturer_id 
mcu_id 0052002f324d500220313256
signature 
# name
name CLOUD-149
# feature
feature -RX_PARALLEL_PWM
feature RX_SERIAL
# serial
serial 0 64 115200 57600 0 115200
serial 2 2048 115200 57600 0 115200
# aux
aux 0 0 0 1300 1700 0 0
aux 1 1 1 1300 1700 0 0
# master
set acc_calibration = 103,86,-27
set mag_hardware = NONE
set serialrx_provider = SBUS
set dshot_idle_value = 300
set motor_pwm_protocol = DSHOT600
set osd_vbat_pos = 2092
set osd_tim_1_pos = 2082
set osd_vtx_channel_pos = 2104
set osd_craft_name_pos = 2507
# profile
profile 0
# restore original profile selection
profile 0
# rateprofile
rateprofile 0
# restore original rateprofile selection
rateprofile 0
# save configuration
save

Aktuelle Kopterheld Coupons, Gutscheine auf Blog, Telegram oder Facebook:
https://kopterheld.tv/
https://t.me/KopterHeld
https://www.facebook.com/kopterheld/

Mein Equipment:
DJI Digital FPV System – https://www.banggood.com/custlink/mGvK0KF1Em
Fatshark Dominator HDO2 – https://www.banggood.com/custlink/KmGKeeY4pN
ImmersionRC RapidFIRE – https://www.banggood.com/custlink/vm3v6vafP1
Taranis X9D Plus SE 2019 – https://www.banggood.com/custlink/v3mKeGLLp6
Jumper 4IN1 Multimodul – https://www.banggood.com/custlink/vGvGNp7s07
FrSky R-XSR – https://www.banggood.com/custlink/DGvDgKOu8B
CADDX Ratel – https://www.banggood.com/custlink/KKKm6mLf9Q

Youtube – https://www.youtube.com/kopterheld
Facebook – https://www.facebook.com/kopterheld/
Blog – https://kopterheld.tv/
RCGroups – https://goo.gl/JYP87D
Telegram – https://t.me/KopterHeld
Instagram – https://instagram.com/kopterheld
Twitter – https://twitter.com/kopterheld